DIGICOM SPA

LEONARDO 33.6, LEONARDO 33.6 MAC

Card Type                    Modem
Chip Set                     Unidentified
Maximum Modem Rate           33.6Kbps
Maximum Fax Rate             14.4Kbps
Data Modulation Protocol     ITU-T V.21, V.22, V.22bis,V.23, V.32,
                             V.32bis, V.34
Fax Modulation Protocol      V.17, V.29, V.27ter
Error Correction/Compression MNP5, MNP10, V.42, V.42bis
Fax Class                    Class I
Data Bus                     PCMCIA

                                                                      54981

                           SUPPORTED COMMAND SET

                             Basic AT Commands

  AT, A/

  A, B, E, H, L, M, O, P, Q, V, W, X, Y, Z

  &C, &P, &T, &V, &W, &Y, &Z

                           Extended AT commands

  \A, \B, \K, \N

  %C, %E, %L, %Q

                                S Registers

  S0, S1, S2, S3, S4, S5, S6 ,S7, S8, S9, S10, S12, S18, S29, S30, S32,
  S33, S95

                             Special commands

  +MS, -K



  Note: See MHI Help File for full command documentation.

                         PROPRIETARY AT COMMAND SET

                            AUTO-MODE DETECTION

  Type:                  Configuration

  Format:                AT [cmds] Nn [cmds]

  Description:           Selects various options for the automatic
                         detection and negotiation of protocols during
                         the handshake process if the modem is
                         communicating with a remote modem of dissimilar
                         speed.

        Command                              Function

          N0             Auto-mode detection disabled

          N1             Auto-mode detection enabled

                            COMMUNICATIONS MODE

  Type:           Configuration

  Format:         AT [cmds] &Qn [cmds]

  Description:    Selects communications mode options

    Command                                Mode

      &Q0         Asynchronous mode, serial port speed follows connect
                  speed.

      &Q5         Error correction mode

      &Q6         Buffered asynchronous mode

                           DATA SET READY (DSR)

  Type:          Configuration

  Format:        AT [cmds] &Sn [cmds]

  Description:   Selects DSR options

    Command                              Function

      &S0        DSR forced high

      &S1        DSR high only while modem is handshaking or connected

                         DATA TERMINAL READY (DTR)

  Type:          Configuration

  Format:        AT [cmds] &Dn [cmds]

  Description:   Selects modem response to DTR

    Command                              Function

      &D0        DTR override

      &D1        DTR toggle causes online command mode

      &D2        Normal DTR operations

      &D3        Resets on receipt of DTR

                                   DIAL

  Type:                  Immediate

  Format:                AT [cmds] D<#> [cmds]

  Description:           Dials telephone number according to any
                         modifiers included in the string

  Note:                  Any combination of modifiers can be used to
                         produce the desired dial functions in sequence.

        Command                              Function

           DL            Re-dial last number

           DP            Pulse dialing enabled

          DS=n           Dial stored telephone number n

           DT            Tone dialing enabled

           DW            Dialing resumed following dial tone detection

           D,            Dialing paused

           D!            Flash function initiated. Modem commanded to go
                         off-hook for specified time before returning
                         on-hook.

           D@            Wait for Quite Answer function enabled. Modem
                         waits until a "quiet answer," a ring-back signal
                         followed by 5 seconds of silence

           D;            Modem returned to idle state after dialing. The
                         semicolon can only be placed at the end of the
                         dial command.

           D^            Toggle calling tone

                          FACTORY DEFAULT PROFILE

  Type:             Configuration

  Format:           AT [cmds] &F [cmds]

  Description:      Sets values in active profile to values found in the
                    default profile

     Command                              Function

       &F0          Factory default profile 0

       &F1          Factory default profile 1

                               FLOW CONTROL

  Type:          Configuration

  Format:        AT [cmds] &Kn [cmds]

  Description:   Enables flow control options

    Command                              Function

      &K0        Flow control disabled

      &K3        RTS/CTS flow control enabled

      &K4        XON/XOFF flow control enabled

      &K5        Transparent XON/XOFF flow control enabled

      &K6        RTS/CTS and XON/XOFF flow control enabled

                                GUARD TONE

  Type:           Configuration

  Format:         AT [cmds] &Gn [cmds]

  Description:    Commands the modem to transmit a guard tone in
                  V.22/V.22bis

    Command                              Function

      &G0         Guard tone disabled

      &G2         1800Hz guard tone enabled

                            REPORT INFORMATION

  Type:          Immediate

  Format:        AT [cmds] In [cmds]

  Description:   Displays information requested

    Command                              Function

       I0        Reports maximum line speed

       I1        Reports product type

       I2        Reports checksum firmware

       I3        Reports product name

       I4        Reports firmware release

       I5        Reports active Country Code

                                  RTS/CTS

  Type:                 Configuration

  Format:               AT [cmds] &Rn [cmds]

  Description:          Selects RTS/CTS options

       Command                              Function

         &R0            In asynchronous mode, C106 is controlled
                        according to V.25 handshake recommendation

         &R1            In synchronous mode, C106 follows flow control

                          EXTENDED AT COMMAND SET

                            LINE SIGNAL QUALITY

  Type:          Immediate

  Format:        AT [cmds] %Q [cmds]

  Range:         000-127

  Unit:          Unidentified

  Description:   Returns a value which indicates line signal quality

                              SPECIAL COMMANDS

                        MNP10 - POWER LEVEL ADJUST

  Type:                Configuration

  Format:              AT [cmds] -SEC=n [cmds]

  Range:               0-30

  Unit:                -1dBm

  Description:         Controls automatic transmit power level adjustment
                       during MNP 10 link negotiation

       Command                              Function

       -SEC=0          MNP10 disabled. Transmission level is set in the
                       S91 register

  -SEC=1, [tx_lev]     MNP10 enabled. Set transmit level

                            S(status) REGISTERS

                         TRANSMISSION LEVEL - FAX

  Type:          Register

  Format:        AT [cmds] S92=n [cmds]

  Range:         3-15

  Unit:          -1 dBm

  Description:   Sets the signal level for transmission while in fax mode

                     TRANSMISSION LEVEL - LEASED-LINE

  Type           Register or Configuration

  Format         AT [cmds] S91=n [cmds]

  Range          3-15

  Unit           -1 dBm

  Description    Sets the signal level for transmission over leased-lines